Why 2.54 is exact
Before 1959 the United States defined the yard as 3600/3937 of a meter. In 1959 it was redefined as exactly 0.9144 meter, which made the new yard shorter than the old one by two parts in a million [1]. Since then the inch has been 25.4 mm exactly, and the U.S. and British inches have been identical [1]. A foot is therefore exactly 30.48 cm (0.3048 m) [2].
The older U.S. survey foot (1200/3937 m) survived in land surveying for decades. NIST and NOAA retired it at the end of 2022, and from January 1, 2023 the international foot applies to all uses except historic records [1][2]. If you see an old U.S. survey plan, the difference is only 2 parts in a million: about 0.4 mm over 200 m.
Reading a tape measure with both scales
A dual tape shows centimeters and millimeters on one edge and inches on the other. On the inch edge the lines get shorter as the fractions get smaller: the longest line between two inch numbers is 1/2, then 1/4, then 1/8, and the shortest is 1/16. One sixteenth of an inch is 1.5875 mm, so it is a little wider than one millimeter line.
To use the fraction column, read the whole number first, then count sixteenths past it. For example, 25 cm is 9.84 in, which is 9 13/16 in: three sixteenths short of the 10-inch line.
- 1 cm ≈ 3/8 in (0.39 in)
- 5 cm ≈ 1 15/16 in (1.97 in)
- 15 cm ≈ 5 7/8 in (5.91 in)
- 30 cm ≈ 11 13/16 in (11.81 in): a 30 cm ruler is about 3/16 in shorter than a 12-inch ruler
- 60 cm ≈ 23 5/8 in (23.62 in)
- 100 cm ≈ 39 3/8 in (39.37 in)
Mental math: three shortcuts and how wrong they are
Every shortcut trades accuracy for speed. The table shows how far each one drifts from the exact value (cm ÷ 2.54).
- Multiply by 0.4 (or divide by 2.5): always 1.6% too high. At 100 cm it gives 40 in instead of 39.37 in, which is 1.6 cm too long. Fine for a rough idea, not for anything that has to fit.
- Multiply by 0.39: always about 0.9% too low. At 100 cm it gives 39.0 in, 9.4 mm short.
- Multiply by 0.4, then take off 1/16 inch for every 10 cm: almost exact. 10 cm gives 3 15/16 in; 200 cm gives 80 − 20/16 = 78 3/4 in, against an exact 78.74 in. The error is 0.25 mm over 2 meters.
- Going the other way, inches × 2.5 is 1.6% too low: 72 in becomes 180 cm instead of 182.88 cm, a gap of almost 3 cm in a height.
Where inches are still used
In the United States, both the SI (metric) and U.S. customary units are in use, and NIST recommends calling the inch-based system "U.S. customary" rather than "Imperial" [1]. Since 1988, U.S. federal policy has named the metric system the preferred system for trade and commerce, while allowing traditional units in non-business activities [1].
In the United Kingdom, the law requires metric units for trade, with only a few exceptions such as draught beer and cider by the pint [3]. Sellers may add an inch or foot figure, but the metric figure must also be shown and must be the more prominent of the two [3].
Several international products keep inch sizes everywhere, even in metric countries:
- Car tyres: in a size such as 205/55 R17, 205 is the section width in millimeters and 17 is the wheel diameter in inches [4]. A 17-inch wheel is 431.8 mm.
- Screens: sizes are diagonal measurements. Apple, for example, states that the iPad mini screen is 8.5 inches when measured diagonally as a rectangle, and that the actual viewable area is less [5]. 8.5 in is 21.59 cm.
- Pipes: inch pipe sizes are names, not measurements. A 2-inch Schedule 40 PVC pipe has an outside diameter of 2.375 in (60.3 mm) and an inside diameter of 2.047 in (52.0 mm) [6]. Converting "2 inch" to 5.08 cm will not find the right fitting.
Common rounding mistakes
Rounding too early is the most frequent error. Using 2.5 instead of 2.54 seems harmless, but the difference grows with length: over 100 cm it is 0.63 in (1.6 cm), and over 200 cm it is 1.26 in (3.2 cm).
The second mistake is rounding the inches first and then converting back. 152 cm is 59.84 in; round it to 60 in and convert back and you get 152.4 cm. Keep the original metric figure and convert only once.
The third is mixing up decimal inches and fractions. 5.5 in is 5 1/2 in, but 5.05 in is not 5 1/20 on a tape; it is closest to 5 1/16 in. Use the fraction column when you will be marking a tape or ruler.
For heights, round to 1/8 inch before splitting into feet. 183 cm is 72.05 in, which rounds to exactly 6 ft 0 in, while 160 cm is 62.99 in, or 5 ft 3 in.
Using the chart for sewing, crafts and boxes
Sewing patterns often round conversions. A U.S. extension guide gives the standard seam allowance as 5/8 inch and writes it as 1.5 cm [7]. The exact value of 5/8 inch is 15.875 mm, so a metric pattern with a 1.5 cm allowance and an inch pattern with 5/8 in differ by under 0.4 mm per seam. The same guide notes that lingerie and some knit patterns use narrower allowances, so check the pattern itself [7].
For shipping boxes and furniture, measure in the unit the seller or carrier uses and round up, never down: a box with an inside length of 40 cm (15.75 in) will not hold an item listed as 16 in.
Scaling a printed table does not change its numbers, but scaling does change a printed ruler or sewing template. Choose "Actual size" in the print dialog, which prints without scaling, rather than "Fit" [8]. Then check the result with a bank card: its long side is 85.60 mm, or 3.37 in [9].
Frequently asked questions
How do I convert cm to inches?
Divide the centimeters by 2.54. For example, 50 cm ÷ 2.54 = 19.69 in. The factor is exact because the inch is defined as 25.4 mm [1].
Is 2.5 cm the same as 1 inch?
No. One inch is 2.54 cm, so 2.5 cm is 0.98 in. The 0.4 mm gap per inch adds up to 1.6 cm over a meter.
What is 30 cm in inches?
30 cm is 11.81 in, or about 11 13/16 in. A 30 cm ruler is 3/16 in shorter than a 12-inch ruler; 12 inches is 30.48 cm.
How many cm are in a foot?
Exactly 30.48 cm, because the international foot is defined as 0.3048 m [2]. Six feet is therefore 182.88 cm.
What is 170 cm in feet and inches?
170 cm is 66.93 in. Rounded to the nearest 1/8 inch, that is 66 7/8 in, which is 5 ft 6 7/8 in.
Sources
- [1]NIST Handbook 44 (2024), Appendix B: Units and Systems of Measurement
- [2]NIST: Revised unit conversion factors
- [3]UK Office for Product Safety and Standards: Choice on units of measurement, guidance on markings and sales
- [4]Michelin: How to read tire markings and sidewall codes
- [5]PEX Universe: 2 inch x 10 ft PVC pipe, Schedule 40 DWV
- [6]Apple: iPad mini technical specifications
- [7]Oregon State University Extension: Plain Seams and Seam Finishes (4-H 320-19)
- [8]Adobe Help: Adjust page size for printing PDFs in Acrobat
- [9]ISO/IEC 7810 Identification cards: Physical characteristics (ANSI Webstore)